A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
We've stumbled upon this post on Installing A Bathtub directly below on the internet and think it made perfect sense to share it with you over here.
Mounting a bath tub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and occasionally, tiling skills. Replacing an old tub with a new one is additionally a reasonably difficult task. If the old bathtub is conveniently easily accessible, the job can move speedily; if you need to open a wall to remove the old tub as well as position the brand-new bathtub, the task is much harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to move out the old bathtub and embeded in the brand-new one. Make sure you have actually certified on your own for the work as well as are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed task, it is far better to think about employing one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will help you install a brand-new bathtub in your bathroom if you have already gotten a new bathtub and don't require to alter the arrangement of your previous water supply pipes.
Your devices as well as material checklist should consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water staying in the system. The procedure of removing the existing faucets can be quite troublesome as a result of the limited gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel all set for the remaining water that will originate from the pipelines. When the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning during this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any kind of old sealing substance.
Prior to going on to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in area in between the faucet as well as the sink. Protect the tap in position with the manufacturer given backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular faucet adapters. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of both wooden boards under its feet, place the tub in the needed position. The wood boards are handy in evenly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by examining the level and adjusting the feet on the tub till the level reviews degree.
To mount faucets, fit the bottom of the furthest versatile tap port to the appropriate supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leakages and also tighten them if required. Load the tub and likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Finally, fix the bath paneling as explained in the maker's user's manual. Tiling and securing around the bathtub needs to wait until the bath tub has actually been made use of at the very least once as this will certainly resolve it right into its final position.
Preparing for the Setup
First of all, the supporting frame supplied with the bathroom must be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to make sure that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the taps unit to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its last setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate enough to split an inflexible seal, causing the water to permeate the wall in between the bathroom and also the tiling, leading to complications with moisture and feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and also fittings. They are sold in tubes and cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealer can fracture rather early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise conveniently offered on the market. It is a good idea to fit the floor tiles making use of waterproof or waterproof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you liked our post about How to Install a Bathtub Yourself. Many thanks for taking the time to read our content. Sharing is good. You won't know, you may just be helping someone out. We love reading our article about Tools You Need to Install a New Bathtub .
Your solution? Just a ring. Report this page